Categories FAQ

Often asked: 2005 chrysler 300 warning lights?

What does the lightning bolt mean on a 2006 Chrysler 300?

Hi There, The red lightning bolt indicates that there is a problem wit the electronic throttle control unit. Slowly depress the accelerator pedal all the way to the floor. Slowly release the accelerator pedal until it is all the way back up at the rest position. Turn the ignition key to “OFF” position.

What does the lightning bolt warning light mean?

This is the Electronic Throttle Control (ETC) Indicator symbol. This light, a lightning bolt between reversed brackets or parenthesis, will illuminate if there is a problem in the electronic throttle control system. As an electronic system, it can sometimes be reset with a restart.

What does red light mean on Chrysler 300?

if the light is light solid red, it means that the WCM can‘t read the SKIM in the key and you have an invalid key code error. this happens if the battery in the key is getting low, if the WCM didn’t read the key correctly more than (3 I think) times on a successful start, or if there is a problem with the WCM.

You might be interested:  Quick Answer: Bmw e30 supercharger kit?

What does the red lightning bolt mean on my Chrysler 200?

This lightning bolt refers to an Electronic Throttle Control problem, or an ETC error. It happens due to a damaged throttle controller. The system controls the air-fuel mixture that goes into the engine.

How do I reset my 2006 Chrysler 300?

To reset the chrysler 300 security system insert the ignition key and turn it to the on position and then try to start the engine (crank over), the engine will not start. with the key still in the run spot, wait 10 minutes, and the safety light will flash and then go out. turn the key off and wait for 5 seconds.

How do I reset my Chrysler 300?

How to Reset the Chrysler 300 Key

  1. Insert a valid key into the ignition.
  2. Turn the ignition switch to “On” for longer than 3 seconds but no longer than 15 seconds.
  3. Turn the ignition off.
  4. Insert the second valid key into the ignition.
  5. Turn the ignition switch to “On.”

Can I drive with the throttle control warning light on?

Can I drive with the throttle control light on? Yes, usually, but you should go straight to a repair shop. There can be many different causes for the throttle control warning light, so a proper diagnosis is key.

How do I reset my electronic throttle control system?

Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.

You might be interested:  Quick Answer: Bmw m4 coupe weight?

How do I reset my electronic throttle control?

Make sure that the accelerator pedal is fully released. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds.

What would cause a Chrysler 300 not to start?

While there are a variety of reasons your Chrysler 300 won’t start, the most common 3 are a dead battery, an alternator problem, or failed starter.

How do you reset the electronic throttle control manual on a Chrysler 300?

Premium Member

  1. Insert ignition key and turn to “ON” (not start).
  2. Wait for all idiot lights to go out.
  3. Slowly depress the accelerator pedal all the way to the floor.
  4. Slowly release the accelerator pedal until it’s all the way back up.
  5. Turn the ignition key to “OFF”.
  6. Start the engine.

How do you use the remote on a Chrysler 300?

Instructions for the Chrysler 300 Car Remote Car Starter

  1. Push the “Start” button on the remote within close enough proximity for the car’s receiver to get the signal.
  2. Avoid using the remote starter feature while your car is in an enclosed space.
  3. Insert your car key into the ignition bezel before hitting the brake or opening your trunk.

How much does it cost to fix a throttle control?

The Best in Auto Repair



The average cost for throttle body replacement is between $577 and $692. Labor costs are estimated between $95 and $120 while parts are priced between $482 and $572. This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed.

You might be interested:  Quick Answer: Audi tire pressure sensor reset?

How much does it cost to fix electronic throttle control?

Electronic Throttle Control Repair Cost – Here’s What You Need To Know. Since this is such a key part to every car’s internal system, the average cost for this repair can be quite pricey – the average electronic throttle control repair cost comes out to around $645!

1 звезда2 звезды3 звезды4 звезды5 звезд (нет голосов)
Loading...

Leave a Reply

Your email address will not be published. Required fields are marked *